单级入轨

冒险之星是一个单级入轨项目提案。

单级入轨（英語：Single-stage-to-orbit，缩写：SSTO）是从地面发射一个航天器直接入轨，不抛弃燃料箱、发动机或其他主要部件，属于可重複使用發射系統的一种。[1]目前，尚没有从地球发射的单级入轨系统被制成，实际使用的都是一次性使用运载系统多级火箭。[2]

理论上，使用化学能驱动的火箭发动机能实现从地球的单级入轨。但挑战在于：轨道速度要超过7,400米每秒（27,000公里每小時；17,000英里每小時）、起飞阶段克服地球稠密大气层的阻力，再入阶段的热防护，综合成本的竞争力。[3]

在其他质量较小且没有大气层的天体表面发射单级入轨航天器是现实可行的，如火星、月球。阿波罗登月的登月舱、苏联的几艘无人自动登月返回的月球号系列探测器等都实现了月面的单级入轨。

历史

早期概念

ROMBUS概念图

二十世纪中叶前，对太空旅行的研究还很少。1960年代，这种工艺的一些早期概念设计开始涌现。[4]

单级入轨最早的概念之一是道格拉斯飞行器公司工程师Philip Bono（英语：Philip Bono）提出的一次性的一级轨道太空卡车（One stage Orbital Space Truck）[5][6]。另也提出了一个名为“ROOST”的可重用版本。

已隱藏部分未翻譯内容，歡迎參與翻譯。

Another early SSTO concept was a reusable launch vehicle named NEXUS which was proposed by Krafft Arnold Ehricke in the early 1960s. It was one of the largest spacecraft ever conceptualized with a diameter of over 50 metres and the capability to lift up to 2000 short tons into Earth orbit, intended for missions to further out locations in the solar system such as Mars.[7][8] The North American Air Augmented VTOVL from 1963 was a similarly large craft which would have used ramjets to decrease the liftoff mass of the vehicle by removing the need for large amounts of liquid oxygen while traveling through the atmosphere.[9]

From 1965, Robert Salked investigated various single stage to orbit winged spaceplane concepts. He proposed a vehicle which would burn hydrocarbon fuel while in the atmosphere and then switch to hydrogen fuel for increasing efficiency once in space.[10][11][12]

Further examples of Bono's early concepts (prior to the 1990s) which were never constructed include:

• ROMBUS (Reusable Orbital Module, Booster, and Utility Shuttle), another design from Philip Bono.[13][14] This was not technically single stage since it dropped some of its initial hydrogen tanks, but it came very close.
• Ithacus, an adapted ROMBUS concept which was designed to carry soldiers and military equipment to other continents via a sub-orbital trajectory.[15][16]
• Pegasus, another adapted ROMBUS concept designed to carry passengers and payloads long distances in short amounts of time via space.[17]
• SASSTO, another launch vehicle concept.[18]
• Hyperion, yet another Philip Bono concept which used a sled to build up speed before liftoff to save on the amount of fuel which had to be lifted into the air.[19]

Around 1985 the NASP project was intended to launch a scramjet vehicle into orbit, but funding was stopped and the project cancelled.[20] At around the same time, the HOTOL tried to use precooled jet engine technology, but failed to show significant advantages over rocket technology.[21]

DC-X技术

主条目：McDonnell Douglas DC-X

The maiden flight of the DC-X

The DC-X, short for Delta Clipper Experimental, was an uncrewed one-third scale vertical takeoff and landing demonstrator for a proposed SSTO. It is one of only a few prototype SSTO vehicles ever built. Several other prototypes were intended, including the DC-X2 (a half-scale prototype) and the DC-Y, a full-scale vehicle which would be capable of single stage insertion into orbit. Neither of these were built, but the project was taken over by NASA in 1995, and they built the DC-XA, an upgraded one-third scale prototype. This vehicle was lost when it landed with only three of its four landing pads deployed, which caused it to tip over on its side and explode. The project has not been continued since.^[來源請求]

Roton

主条目：Rotary Rocket

From 1999 to 2001 Rotary Rocket attempted to build a SSTO vehicle called the Roton. It received a large amount of media attention and a working sub-scale prototype was completed, but the design was largely impractical.[22]

方法

There have been various approaches to SSTO, including pure rockets that are launched and land vertically, air-breathing scramjet-powered vehicles that are launched and land horizontally, nuclear-powered vehicles, and even jet-engine-powered vehicles that can fly into orbit and return landing like an airliner, completely intact.

For rocket-powered SSTO, the main challenge is achieving a high enough mass-ratio to carry sufficient propellant to achieve orbit, plus a meaningful payload weight. One possibility is to give the rocket an initial speed with a space gun, as planned in the Quicklaunch project.^[來源請求]

For air-breathing SSTO, the main challenge is system complexity and associated research and development costs, material science, and construction techniques necessary for surviving sustained high-speed flight within the atmosphere, and achieving a high enough mass-ratio to carry sufficient propellant to achieve orbit, plus a meaningful payload weight. Air-breathing designs typically fly at supersonic or hypersonic speeds, and usually include a rocket engine for the final burn for orbit.[1]

Whether rocket-powered or air-breathing, a reusable vehicle must be rugged enough to survive multiple round trips into space without adding excessive weight or maintenance. In addition a reusable vehicle must be able to reenter without damage, and land safely.^[來源請求]

While single-stage rockets were once thought to be beyond reach, advances in materials technology and construction techniques have shown them to be possible. For example, calculations show that the Titan II first stage, launched on its own, would have a 25-to-1 ratio of fuel to vehicle hardware.[23] It has a sufficiently efficient engine to achieve orbit, but without carrying much payload.[24]

Dense versus hydrogen fuels

Hydrogen might seem the obvious fuel for SSTO vehicles. When burned with oxygen, hydrogen gives the highest specific impulse of any commonly used fuel: around 450 seconds, compared with up to 350 seconds for kerosene.^[來源請求]

Hydrogen has the following advantages:^[來源請求]

• Hydrogen has nearly 30% higher specific impulse (about 450 seconds vs. 350 seconds) than most dense fuels.
• Hydrogen is an excellent coolant.
• The gross mass of hydrogen stages is lower than dense-fuelled stages for the same payload.
• Hydrogen is environmentally friendly.

However, hydrogen also has these disadvantages:^[來源請求]

• Very low density (about 1⁄7 of the density of kerosene) – requiring a very large tank
• Deeply cryogenic – must be stored at very low temperatures and thus needs heavy insulation
• Escapes very easily from the smallest gap
• Wide combustible range – easily ignited and burns with a dangerously invisible flame
• Tends to condense oxygen which can cause flammability problems
• Has a large coefficient of expansion for even small heat leaks.

These issues can be dealt with, but at extra cost.^[來源請求]

While kerosene tanks can be 1% of the weight of their contents, hydrogen tanks often must weigh 10% of their contents. This is because of both the low density and the additional insulation required to minimize boiloff (a problem which does not occur with kerosene and many other fuels). The low density of hydrogen further affects the design of the rest of the vehicle: pumps and pipework need to be much larger in order to pump the fuel to the engine. The end result is the thrust/weight ratio of hydrogen-fueled engines is 30–50% lower than comparable engines using denser fuels.^[來源請求]

This inefficiency indirectly affects gravity losses as well; the vehicle has to hold itself up on rocket power until it reaches orbit. The lower excess thrust of the hydrogen engines due to the lower thrust/weight ratio means that the vehicle must ascend more steeply, and so less thrust acts horizontally. Less horizontal thrust results in taking longer to reach orbit, and gravity losses are increased by at least 300米每秒（1,100公里每小時；670英里每小時）. While not appearing large, the mass ratio to delta-v curve is very steep to reach orbit in a single stage, and this makes a 10% difference to the mass ratio on top of the tankage and pump savings.^[來源請求]

The overall effect is that there is surprisingly little difference in overall performance between SSTOs that use hydrogen and those that use denser fuels, except that hydrogen vehicles may be rather more expensive to develop and buy. Careful studies have shown that some dense fuels (for example liquid propane) exceed the performance of hydrogen fuel when used in an SSTO launch vehicle by 10% for the same dry weight.[25]

In the 1960s Philip Bono investigated single-stage, VTVL tripropellant rockets, and showed that it could improve payload size by around 30%.[26]

Operational experience with the DC-X experimental rocket has caused a number of SSTO advocates to reconsider hydrogen as a satisfactory fuel. The late Max Hunter, while employing hydrogen fuel in the DC-X, often said that he thought the first successful orbital SSTO would more likely be fueled by propane.^[來源請求]

单台发动机应对所有高度

Some SSTO concepts use the same engine for all altitudes, which is a problem for traditional engines with a bell-shaped nozzle. Depending on the atmospheric pressure, different bell shapes are optimal. Engines operating in the lower atmosphere have shorter bells than those designed to work in vacuum. Having a bell that is only optimal at a single altitude lowers the overall engine efficiency.^[來源請求]

One possible solution would be to use an aerospike engine, which can be effective in a wide range of ambient pressures. In fact, a linear aerospike engine was to be used in the X-33 design.^[來源請求]

Other solutions involve using multiple engines and other altitude adapting designs such as double-mu bells or extensible bell sections.^[來源請求]

Still, at very high altitudes, the extremely large engine bells tend to expand the exhaust gases down to near vacuum pressures. As a result, these engine bells are counterproductive due to their excess weight. Some SSTO concepts use very high pressure engines which permit high ratios to be used from ground level. This gives good performance, negating the need for more complex solutions.^[來源請求]

Airbreathing SSTO

Skylon spaceplane

Some designs for SSTO attempt to use airbreathing jet engines that collect oxidizer and reaction mass from the atmosphere to reduce the take-off weight of the vehicle.^[來源請求]

Some of the issues with this approach are:^[來源請求]

• No known air breathing engine is capable of operating at orbital speed within the atmosphere (for example hydrogen fueled scramjets seem to have a top speed of about Mach 17).[27] This means that rockets must be used for the final orbital insertion.
• Rocket thrust needs the orbital mass to be as small as possible to minimize propellant weight.
• The thrust-to-weight ratio of rockets that rely on on-board oxygen increases dramatically as fuel is expended, because the oxidizer fuel tank has about 1% of the mass as the oxidizer it carries, whereas air-breathing engines traditionally have a poor thrust/weight ratio which is relatively fixed during the air-breathing ascent.
• Very high speeds in the atmosphere necessitate very heavy thermal protection systems, which makes reaching orbit even harder.
• While at lower speeds, air-breathing engines are very efficient, but the efficiency (Isp) and thrust levels of air-breathing jet engines drop considerably at high speed (above Mach 5–10 depending on the engine) and begin to approach that of rocket engines or worse.
• Lift to drag ratios of vehicles at hypersonic speeds are poor, however the effective lift to drag ratios of rocket vehicles at high g is not dissimilar.

Thus with for example scramjet designs (e.g. X-43) the mass budgets do not seem to close for orbital launch.^[來源請求]

Similar issues occur with single-stage vehicles attempting to carry conventional jet engines to orbit—the weight of the jet engines is not compensated sufficiently by the reduction in propellant.[28]

On the other hand, LACE-like precooled airbreathing designs such as the Skylon spaceplane (and ATREX) which transition to rocket thrust at rather lower speeds (Mach 5.5) do seem to give, on paper at least, an improved orbital mass fraction over pure rockets (even multistage rockets) sufficiently to hold out the possibility of full reusability with better payload fraction.[29]

It is important to note that mass fraction is an important concept in the engineering of a rocket. However, mass fraction may have little to do with the costs of a rocket, as the costs of fuel are very small when compared to the costs of the engineering program as a whole. As a result, a cheap rocket with a poor mass fraction may be able to deliver more payload to orbit with a given amount of money than a more complicated, more efficient rocket.^[來源請求]

Launch assists

Many vehicles are only narrowly suborbital, so practically anything that gives a relatively small delta-v increase can be helpful, and outside assistance for a vehicle is therefore desirable.^[來源請求]

Proposed launch assists include:^[來源請求]

• sled launch (rail, maglev including Bantam, MagLifter, and StarTram, etc.)[30]
• air launch or aircraft tow
• in-flight fueling
• Lofstrom launch loop/space fountains

And on-orbit resources such as:^[來源請求]

• Space tether
• tugs

核推进

主条目：Nuclear propulsion

Due to weight issues such as shielding, many nuclear propulsion systems are unable to lift their own weight, and hence are unsuitable for launching to orbit. However some designs such as the Orion project and some nuclear thermal designs do have a thrust to weight ratio in excess of 1, enabling them to lift off. Clearly one of the main issues with nuclear propulsion would be safety, both during a launch for the passengers, but also in case of a failure during launch. No current program is attempting nuclear propulsion from Earth's surface.^[來源請求]

Beam-powered propulsion

主条目：Beam-powered propulsion

Because they can be more energetic than the potential energy that chemical fuel allows for, some laser or microwave powered rocket concepts have the potential to launch vehicles into orbit, single stage. In practice, this area is not possible with current technology.^[來源請求]

单级入轨的设计难题

The design space constraints of SSTO vehicles were described by rocket design engineer Robert Truax:

Using similar technologies (i.e., the same propellants and structural fraction), a two-stage-to-orbit vehicle will always have a better payload-to-weight ratio than a single stage designed for the same mission, in most cases, a very much better [payload-to-weight ratio]. Only when the structural factor approaches zero [very little vehicle structure weight] does the payload/weight ratio of a single-stage rocket approach that of a two-stage. A slight miscalculation and the single-stage rocket winds up with no payload. To get any at all, technology needs to be stretched to the limit. Squeezing out the last drop of specific impulse, and shaving off the last pound, costs money and/or reduces reliability.[31]

The Tsiolkovsky rocket equation expresses the maximum change in velocity any single rocket stage can achieve:

${\displaystyle \Delta v=I_{\text{sp}}\cdot g_{0}\ln(MR)}$

where:

${\displaystyle \Delta v}$ (delta-v) is the maximum change of velocity of the vehicle,

${\displaystyle I_{\text{sp}}}$ is the propellant specific impulse,

${\displaystyle g_{0}}$ is the standard gravity,

${\displaystyle MR}$ is the vehicle mass ratio,

${\displaystyle \ln }$ refers to the natural logarithm function.

The mass ratio of a vehicle is defined as a ratio the initial vehicle mass when fully loaded with propellants ${\displaystyle \left(m_{i}\right)}$ to the final vehicle mass ${\displaystyle \left(m_{f}\right)}$ after the burn:

${\displaystyle MR={\frac {m_{i}}{m_{f}}}={\frac {m_{p}+m_{s}+m_{\text{pl}}}{m_{s}+m_{\text{pl}}}}}$

where:

${\displaystyle m_{i}}$ is the initial vehicle mass or the gross liftoff weight ${\displaystyle \left(GLOW\right)}$,

${\displaystyle m_{f}}$ is the final vehicle mass after the burn,

${\displaystyle m_{s}}$ is the structural mass of vehicle,

${\displaystyle m_{p}}$ is the propellant mass,

${\displaystyle m_{\text{pl}}}$ is the payload mass.

The propellant mass fraction (${\displaystyle \zeta }$) of a vehicle can be expressed solely as a function of the mass ratio:

${\displaystyle \zeta ={\frac {m_{p}}{m_{i}}}={\frac {m_{i}-m_{f}}{m_{i}}}=1-{\frac {m_{f}}{m_{i}}}=1-{\frac {1}{MR}}={\frac {MR-1}{MR}}}$

The structural coefficient (${\displaystyle \lambda }$) is a critical parameter in SSTO vehicle design.[32] Structural efficiency of a vehicle is maximized as the structural coefficient approaches zero. The structural coefficient is defined as:

Comparison of growth factor sensitivity for Single-Stage-to-Orbit (SSTO) and restricted stage Two-Stage-to-Orbit (TSTO) vehicles. Based on a LEO mission of Delta v = 9.1 km/s and payload mass = 4500 kg for range of propellant Isp.

${\displaystyle \lambda ={\frac {m_{s}}{m_{p}+m_{s}}}={\frac {m_{s}}{m_{i}-m_{\text{pl}}}}={\frac {\frac {m_{s}}{m_{i}}}{1-{\frac {m_{\text{pl}}}{m_{i}}}}}}$

The overall structural mass fraction ${\displaystyle \left({\frac {m_{s}}{m_{i}}}\right)}$ can be expressed in terms of the structural coefficient:

${\displaystyle {\frac {m_{s}}{m_{i}}}=\lambda \left(1-{\frac {m_{\text{pl}}}{m_{i}}}\right)}$

An additional expression for the overall structural mass fraction can be found by noting that the payload mass fraction ${\displaystyle \left({\frac {m_{\text{pl}}}{m_{i}}}\right)}$, propellant mass fraction and structural mass fraction sum to one:

${\displaystyle 1={\frac {m_{\text{pl}}}{m_{i}}}+{\frac {m_{p}}{m_{i}}}+{\frac {m_{s}}{m_{i}}}={\frac {m_{\text{pl}}}{m_{i}}}+\zeta +{\frac {m_{s}}{m_{i}}}}$

${\displaystyle {\frac {m_{s}}{m_{i}}}=1-\zeta -{\frac {m_{\text{pl}}}{m_{i}}}}$

Equating the expressions for structural mass fraction and solving for the initial vehicle mass yields:

${\displaystyle m_{i}=GLOW={\frac {m_{\text{pl}}}{1-\left({\frac {\zeta }{1-\lambda }}\right)}}}$

This expression shows how the size of a SSTO vehicle is dependent on its structural efficiency. Given a mission profile ${\displaystyle \left(\Delta v,m_{\text{pl}}\right)}$ and propellant type ${\displaystyle \left(I_{\text{sp}}\right)}$, the size of a vehicle increases with an increasing structural coefficient.[33] This growth factor sensitivity is shown parametrically for both SSTO and two-stage-to-orbit (TSTO) vehicles for a standard LEO mission.[34] The curves vertically asymptote at the maximum structural coefficient limit where mission criteria can no longer be met:

${\displaystyle \lambda _{\text{max}}=1-\zeta ={\frac {1}{MR}}}$

In comparison to a non-optimized TSTO vehicle using restricted staging, a SSTO rocket launching an identical payload mass and using the same propellants will always require a substantially smaller structural coefficient to achieve the same delta-v. Given that current materials technology places a lower limit of approximately 0.1 on the smallest structural coefficients attainable,[35] reusable SSTO vehicles are typically an impractical choice even when using the highest performance propellants available.

案例

It is easier to achieve SSTO from a body with lower gravitational pull than Earth, such as the Moon or Mars. The Apollo Lunar Module ascended from the lunar surface to lunar orbit in a single stage.^[來源請求]

A detailed study into SSTO vehicles was prepared by Chrysler Corporation's Space Division in 1970–1971 under NASA contract NAS8-26341. Their proposal (Shuttle SERV) was an enormous vehicle with more than 50,000公斤（110,000英磅） of payload, utilizing jet engines for (vertical) landing.[36] While the technical problems seemed to be solvable, the USAF required a winged design that led to the Shuttle as we know it today.

The uncrewed DC-X technology demonstrator, originally developed by McDonnell Douglas for the Strategic Defense Initiative (SDI) program office, was an attempt to build a vehicle that could lead to an SSTO vehicle. The one-third-size test craft was operated and maintained by a small team of three people based out of a trailer, and the craft was once relaunched less than 24 hours after landing. Although the test program was not without mishap (including a minor explosion), the DC-X demonstrated that the maintenance aspects of the concept were sound. That project was cancelled when it landed with three of four legs deployed, tipped over, and exploded on the fourth flight after transferring management from the Strategic Defense Initiative Organization to NASA.^[來源請求]

The Aquarius Launch Vehicle was designed to bring bulk materials to orbit as cheaply as possible.^[來源請求]

当前开发

Current and previous SSTO projects include the Japanese Kankoh-maru project, ARCA Haas 2C, and the Indian Avatar spaceplane.^[來源請求]

Skylon

主条目：Reaction Engines Skylon

The British Government partnered with the ESA in 2010 to promote a single-stage to orbit spaceplane concept called Skylon.[37] This design was pioneered by Reaction Engines Limited (REL),[38][39] a company founded by Alan Bond after HOTOL was canceled.[40] The Skylon spaceplane has been positively received by the British government, and the British Interplanetary Society.[41] Following a successful propulsion system test that was audited by ESA's propulsion division in mid-2012, REL announced that it would begin a three-and-a-half-year project to develop and build a test jig of the Sabre engine to prove the engines performance across its air-breathing and rocket modes.[42] In November 2012, it was announced that a key test of the engine precooler had been successfully completed, and that ESA had verified the precooler's design. The project's development is now allowed to advance to its next phase, which involves the construction and testing of a full-scale prototype engine.[42][43]

廉价空间飞行的其他方法

Many studies have shown that regardless of selected technology, the most effective cost reduction technique is economies of scale.^[來源請求] Merely launching a large total number reduces the manufacturing costs per vehicle, similar to how the mass production of automobiles brought about great increases in affordability.^[來源請求]

Using this concept, some aerospace analysts believe the way to lower launch costs is the exact opposite of SSTO. Whereas reusable SSTOs would reduce per launch costs by making a reusable high-tech vehicle that launches frequently with low maintenance, the "mass production" approach views the technical advances as a source of the cost problem in the first place. By simply building and launching large quantities of rockets, and hence launching a large volume of payload, costs can be brought down. This approach was attempted in the late 1970s, early 1980s in West Germany with the Democratic Republic of the Congo-based OTRAG rocket.[44]

This is somewhat similar to the approach some previous systems have taken, using simple engine systems with "low-tech" fuels, as the Russian and Chinese space programs still do.

An alternative to scale is to make the discarded stages practically reusable: this is the goal of the SpaceX reusable launch system development program and their Falcon 9, Falcon Heavy, and Starship. A similar approach is being pursued by Blue Origin, using New Glenn.

参见

• 氣尖引擎
• Bristol Spaceplanes（英语：Bristol Spaceplanes）
• British Aerospace HOTOL（英语：British Aerospace HOTOL）
• Kankoh-maru（英语：Kankoh-maru）
• 发射环
• X-33試驗機
• Propellant mass fraction（英语：Propellant mass fraction）
• X-34試驗機
• Orbital ring（英语：Orbital ring）
• Rockwell X-30（英语：Rockwell X-30）
• Roton（英语：Rotary Rocket）
• 超音速燃烧冲压发动机
• 空间电梯
• 航天器推进
• 三级入轨（英语：Three-stage-to-orbit）
• 二级入轨
• 多级火箭
• 冒险之星
• XS-1_(太空飞机)

进一步阅读

• Andrew J. Butrica: Single Stage to Orbit - Politics, Space Technology, and the Quest for Reusable Rocketry. The Johns Hopkins University Press, Baltimore 2004, ISBN 9780801873386.

参考文献

1. Richard Varvill & Alan Bond. A Comparison of Propulsion Concepts for SSTO Reusable Launchers (PDF). JBIS. 2003 [2011-03-05]. （原始内容 (PDF)存档于2011-06-15）. 
2. Dick, Stephen and Lannius, R., "Critical Issues in the History of Spaceflight," NASA Publication SP-2006-4702, 2006.
3. Harry W. Jones (2018). "The Recent Large Reduction in Space Launch Cost"^[失效連結] (PDF). ICES （页面存档备份，存于互联网档案馆）. Retrieved 12 December 2018.
4. Gomersall, Edward. A Single Stage To Orbit Shuttle Concept. Ames Mission Analysis Division Office of Advanced Research and Technology: NASA. 1970-07-20: 54. N93-71495. 
5. Philip Bono and Kenneth William Gatland, Frontiers of Space, ISBN 0-7137-3504-X
6. Wade, Mark. OOST. Encyclopedia Astronautica. [2015-10-18]. （原始内容存档于2011-10-10）.  |url-status=和|dead-url=只需其一 (帮助)
7. Aerospace projects Review 3 (1). [2020-05-06]. （原始内容存档于2021-10-01）. 
8. SP-4221 The Space Shuttle Decision. NASA History. [2015-10-18]. （原始内容存档于2021-10-01）. 
9. Encyclopedia Astronautica - North American Air Augmented VTOVL. [2015-10-18]. （原始内容存档于2016-03-04）. 
10. Salkeld Shuttle. astronautix.com. [2015-06-13]. （原始内容存档于2016-03-15）. 
11. ROBERT SALKELD'S. pmview.com. [2015-06-13]. （原始内容存档于2019-06-11）. 
12. STS-1 Further Reading. nasa.gov. [2015-06-13]. （原始内容存档于2021-10-01）. 
13. Bono, Philip. ROMBUS - An Integrated Systems Concept for a Reusable Orbital Module/Booster And Utility Shuttle. AIAA. June 1963, (AIAA-1963-271) [2020-05-06]. （原始内容存档于2008-12-16）. 
14. Rombus. [2020-05-06]. （原始内容存档于2008-06-11）. 
15. Bono, Philip. "Ithacus" — a new concept of inter-continental ballistic transport (ICBT). AIAA. June 1963, (AIAA-1964-280) [2020-05-06]. （原始内容存档于2008-12-16）. 
16. Ithacus. [2020-05-06]. （原始内容存档于2002-05-28）. 
17. Pegasus VTOVL. [2020-05-06]. （原始内容存档于2016-03-03）. 
18. SASSTO. [2020-05-06]. （原始内容存档于2008-10-06）. 
19. Hyperion SSTO. [2020-05-06]. （原始内容存档于2011-05-13）. 
20. X-30. [2002-08-29]. （原始内容存档于2002-08-29）. 
21. Flight international 1 March 1986
22. Wired 4.05: Insanely Great? or Just Plain Insane?. wired.com. May 1996 [13 June 2015]. （原始内容存档于2012-10-22）. 
23. The titan family. [2009-09-14]. （原始内容存档于2021-10-01）. 
24. Mitchell Burnside-Clapp. A LO2/Kerosene SSTO Rocket Design. February 1997 [2009-09-14]. （原始内容存档于2021-10-01）. 
25. Dr. Bruce Dunn. Alternate Propellants for SSTO Launchers. 1996 [2007-11-15]. 原始内容存档于2014-02-26. 
26. VTOVL. astronautix.com. [2015-06-13]. （原始内容存档于2015-07-02）.  |url-status=和|dead-url=只需其一 (帮助)
27. Mark Wade. X-30. 2007 [2007-11-15]. （原始内容存档于2002-08-29）.  |url-status=和|dead-url=只需其一 (帮助)
28. Richard Varvill & Alan Bond. A Comparison of Propulsions Concepts for SSTO Reusable launchers (PDF). Journal of the British Interplanetary Society: 108–117. 2003 [2007-11-15]. （原始内容 (PDF)存档于2012-06-28）.  |volume=被忽略 (帮助)
29. Cimino, P.; Drake, J.; Jones, J.; Strayer, D.; Venetoklis, P.: "Transatmospheric vehicle propelled by air-turborocket engines" （页面存档备份，存于互联网档案馆）, AIAA, Joint Propulsion Conference, 21st, Monterey, CA, 8–11 July 1985. 10 p. Research supported by the Rensselaer Polytechnic Institute., 07/1985
30. 存档副本. [2020-05-06]. （原始内容存档于2021-10-01）. 
31. London III, Lt Col John R., "LEO on the Cheap", Air University (AFMC) Research Report No. AU-ARI-93-8, October 1994.
32. Hale, Francis, Introduction to Space Flight, Prentice Hall, 1994.
33. Mossman, Jason, "Investigation of Advanced Propellants to Enable Single Stage to Orbit Launch Vehicles", Master's thesis, California State University, Fresno, 2006.
34. Livington, J.W., "Comparative Analysis of Rocket and Air-Breathing Launch Vehicle Systems", Space 2004 Conference and Exhibit, San Diego, California, 2004.
35. Curtis, Howard, Orbital Mechanics for Engineering Students, Third Edition, Oxford: Elsevier, 2010. Print.
36. Mark Wade. Shuttle SERV. 2007 [2010-04-01]. （原始内容存档于2017-04-11）. 
37. UKSA Reviews Skylon and SABRE at Parabolic Arc. parabolicarc.com. [2015-06-13]. （原始内容存档于2015-06-14）. 
38. Reaction Engines Ltd - Frequently Asked Questions. reactionengines.co.uk. [2015-06-13]. （原始内容存档于2015-06-02）. 
39. Archived copy. [2011-03-01]. （原始内容存档于2010-09-26）. 
40. Reaction Engines Limited. reactionengines.co.uk. [2015-06-13]. （原始内容存档于2011-11-08）. 
41. Robert Parkinson. SSTO spaceplane is coming to Great Britain. The Global Herald. 2011-02-22 [2011-02-28]. （原始内容存档于2011-02-23）.  |url-status=和|dead-url=只需其一 (帮助)
42. Skylon spaceplane engine concept achieves key milestone. BBC. 2012-11-28 [2012-11-28]. （原始内容存档于2021-10-01）. 
43. Thomson, Ian. "European Space Agency clears SABRE orbital engines" （页面存档备份，存于互联网档案馆）. The Register. 29 November 2012.
44. 存档副本. [2020-05-06]. （原始内容存档于2021-10-01）. 

外部链接

• A Single-Stage-to-Orbit Thought Experiment （页面存档备份，存于互联网档案馆）
• Why are launch costs so high?, an analysis of space launch costs, with a section critiquing SSTO
• The Cold Equations Of Spaceflight （页面存档备份，存于互联网档案馆） A critique of SSTO by Jeffrey F. Bell.
• Burnout Velocity Vb of a Single 1-Stage Rocket（页面存档备份，存于互联网档案馆）